HPLC Autosamplers

Agilent 1200 HPLC G1329A Autosampler Specifications

GLP Features	Early maintenance feedback (EMF), electronic records of maintenance and errors
Communications	Controller-area network (CAN). GPIB (IEEE-448), RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
Safety Features	Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display
Injection Range	0.1 to 100 µl in 0.1 µl increments Up to 1500 µl with multiple draw (hardware modification required)
Replicate Injections	1 to 99 from one vial
Precision	Typically < 0.5 % RSD of peak areas from 5 to 100 µl Typically < 1 % RSD 1 to 5 µl variable volume
Minimum Sample Volume	1 µl from 5 µl sample in 100 µl microvial, or 1 µl from 10 µl sample in 300 µl microvial
Carryover	Typically < 0.1 %, < 0.05 % with external needle cleaning
Sample Viscosity Range	0.2 to 50 cp
Replicate Injections Per Vial	1 to 99
Sample Capacity	100 × 2-ml vials in 1 tray 40 × 2-ml vials in ½ tray 15 × 6-ml vials in ½ tray (Agilent vials only)
Injection Cycle Time	Typically 50 s depending on draw speed and injection volume

Our Price: $7,395.00

Sale Price: $6,695.00

Money Saved: $700.00

Agilent 1200 HPLC G1367B High Performance Autosampler

Agilent 1200 HPLC G1367B High Performance Autosampler Specifications

GLP Features	Early maintainece feedback (EMF), electronic records of maintainence and errors
Communications	Controller-area network (CAN). RS232C, APG remote standard, optional four external contact closures and BCD vial number output
Safety Features	Leak detection and safe leak handling, low voltages in maintence areas, error detection and display
Injection Range	0.1 to 100 µl in 0.1 µl increments Up to 1500 µl with multiple draw (hardware modification required)
Precision	Typically < 0.25 % RSD from 5 ‚ 100 µl, Typically < 1 % RSD from 1 - 5 µl
Pressure Range	400 bar (5800 psi)
Sample Viscosity Range	0.2 to 5 cp
Sample Capacity	2 × well-plates (MTP) + 10 × 2 ml vials 108 x 2 ml vials in 2 x 54 vial plate plus 10 additional 2 mL vials 30 x 6-mL vials in 2 x 15 vial plate plus 10 additional 2 mL vials 54 Eppendorf tubes (0.5/1.5/2.0mL) in 2 x 27 Eppendorf tube plate
Injection Cycle Time	Typically < 30 s using following standard conditions: Default draw speed: 200 µl/min Default eject speed: 200 µl/min Injection volume: 5 µl
Carry-Over	Typically < 0.01 % using the following conditions: Column: 125 x 4 mm Hypersil ODS, 5 µm Mobile phase: Water/Acetonitrile = 80/20 Flow rate: 1 ml/min Injection volume: 1 µl caffeine (1 mg/ml), 5 µl water to test carryover Outside wash of needle before injection: 20 sec with water using flush port

Our Price: $7,195.00

Sale Price: $6,495.00

Money Saved: $700.00

Agilent 1100 HPLC G1367A Autosampler

Agilent 1100 HPLC G1367A Autosampler Specifications

GLP Features	Early maintainece feedback (EMF), electronic records of maintainence and errors
Communications	Controller-area network (CAN). RS232C, APG remote standard, optional four external contact closures and BCD vial number output
Safety Features	Leak detection and safe leak handling, low voltages in maintence areas, error detection and display
Injection Range	0.1 to 100 µl in 0.1 µl increments Up to 1500 µl with multiple draw (hardware modification required)
Precision	Typically < 0.5 % RSD of peak areas from 5 to 100 µl, Typically < 1 % RSD from 1 to 5 µl
Sample Viscosity Range	0.2 to 5 cp
Sample Capacity	2 × well-plates (MTP) + 10 × 2 ml vials [Not Included] 100 x 2 ml in one tray 40 x 2 ml in half tray [Included]
Injection Cycle Time	Typically < 30 s using following standard conditions: Default draw speed: 200 µl/min Default eject speed: 200 µl/min Injection volume: 5 µl
Carry-Over	Typically < 0.01 % using the following conditions: Column: 125 x 4 mm Hypersil ODS, 5 µm Mobile phase: Water/Acetonitrile = 80/20 Flow rate: 1 ml/min Injection volume: 1 µl caffeine (1 mg/ml), 5 µl water to test carryover Outside wash of needle before injection: 20 sec with water using flush port

Our Price: $5,735.00

Sale Price: $4,575.00

Money Saved: $1,160.00

Agilent 1100 HPLC G1389A MicroALS Autosampler

Agilent 1100 HPLC G1389A MicroALS Autosampler Specifications

Weight	14.2 kg (31.3 lbs)
Dimensions (H x W x D)	200 x 345 x 435 mm (8 x 13.5 x 17 in)
Line Voltage Line frequency	100 to 120 or 220 to 240 VAC, ± 10 % 50 or 60 Hz, ± 5 %
Power consumption (apparent power) Power consumption (active power)	300 VA max. 200 W max.
Ambient operating temperature Ambient non-operating temperature	4 to 55C (41 to 131F) 40 to 70C (-4 to 158F)
Humidity	< 95 %, at 25 to 40C (77 to 104F) non-condensing
Tray	Thermostattable Tray for 100 x 2 ml vials Microvials (100 or 300 µl) with sleeves (reduced cooling performance with microvials)
Settable injection volume	0.01 to 8 µl with small loop capillary 0.01 to 40 µl with extended loop capillary
Precision	Typically < 0.5 % RSD from 5 to 40 µl Typically < 1 % RSD from 1 to 5 µl Typically < 3 % RSD from 0.2 to 1 µl
Minimum sample volume	1 µl from 5 µl sample in 100 µl microvial, or 1 µl from 10 µl sample in 300 µl microvials
Carryover	Typically < 0.1 % without automated needle wash Typically < 0.05 % with external needle cleaning and 1 µl injection volume
Sample viscosity range	0.2 - 5 cp
Recommended pH-range	1.0 - 8.5 solvent with pH < 2.3 should not contain acids which attack stainless steel. Upper pH range is limited by fused silica capillaries
Material in contact with solvent	Stainless steel, sapphire, PTFE, PEEK, fused silica, Vespel
GLP features	Early maintenance feedback (EMF), electronic records of maintenance and errors
Communications	Controller-area network (CAN), GPIB (IEEE-448), RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
Housing	All materials are recyclable

Our Price: $4,155.00

Sale Price: $2,995.00

Money Saved: $1,160.00

Agilent 1260 Infinity I HPLC G1329B Autosampler

Agilent 1260 Infinity HPLC G1329B Autosampler Specifications

Pressure	Operating range 0 to 60 MPa (0 to 600 bar, 0 to 8850 psi)
GLP Features	Early maintenance feedback (EMF), electronic records of maintenance and errors
Communications	Controller-area network (CAN), RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
Safety Features	Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display
Injection Range	0.1 to 100 µl in 0.1 µl increments (recommended 1 µl increments) Up to 1500 µl with multiple draw (hardware modification required)
Replicate Injections	1 to 99 from one vial
Precision	Typically < 0.25 % RSD of peak areas from 5 to 100 µl Typically < 1 % RSD of peak areas from 1 to 5 µl
Minimum Sample Volume	1 µl from 5 µl sample in 100 µl microvial, or 1 µl from 10 µl sample in 300 µl microvial
Carryover	Typically < 0.1 %, < 0.05 % with external needle cleaning
Sample Viscosity Range	0.2 to 50 cp
Metering Devices	Metering pump in high pressure flow path
Sample Capacity	100 x 2 ml vials in 1 tray 40 x 2 ml vials in ½ tray 15 x 6 ml vials in ½ tray (Agilent vials only)
Injection Cycle Time	50 seconds for draw speed 200 µl/min, ejection speed 200 µl/min, injection volume 5 µl

Our Price: $8,795.00

Sale Price: $8,295.00

Money Saved: $500.00

Agilent 1260 Infinity II HPLC G7167A Multisampler

Agilent 1260 Infinity II HPLC G7167A Multisampler Specifications

Injection Range	Default: 0.1 to 100 µL in 0.1 µL increments; optional: 20 µL or 40 µL (using 100 µL analytical head)
Injection Precision	<0.2 % RSD or SD <10 nL, whatever is greater
Injection Linearity	0.9999 in the range of 0.1 to 100 µL
Pressure Range	Up to 800 bar
Sample Viscosity Range	0.2 to 5.0 cP
Sample Capacity	1H Drawer: up to 8 drawers and 16 positions; Shallow well plates (MTP) 2H Drawer: up to 4 drawers and 8 positions; MTP, deep well plates, vials, Eppendorf 3H Drawer: up to 2 drawers and 4 positions; MTP, deep well plates, vials up to 6 mL, Eppendorf
Injection Cycle Time	<10 s using following standard conditions: Default draw speed: 100 µL/min Default eject speed: 400 µL/min Injection volume: 1 µL
Carryover	<0.003 % (30 ppm) Multisampler Standard and Dual Needle <0.0009 % (9 ppm) Multisampler Multiwash
Multiwash	Outer needle wash and seat backflush for carryover reduction with up to 3 different solvents
Dimensions (H x W x D)	12.6 x 15.6 x 18.4 in. (32 x 39.6 x 46.8 cm)
Weight	48.5 lb. (22 kg.)
Electrical Requirements	100 to 240V, 50/60Hz, 180VA

Our Price: $18,995.00

Agilent 1100 HPLC G1313A Autosampler

Agilent 1100 HPLC G1313A Autosampler Specifications

GLP Features	Early maintenance feedback (EMF), electronic records of maintenance and errors
Communications	Controller-area network (CAN). GPIB (IEEE-448), RS232C, APG-remote standard, optional four external contact closures and BCD vial number output
Safety Features	Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display
Injection Range	0.1 to 100 µl in 0.1 µl increments Up to 1500 µl with multiple draw (hardware modification required)
Replicate Injections	1 to 99 from one vial
Precision	Typically < 0.5 % RSD of peak areas from 5 to 100 µl Typically < 1 % RSD of peak areas from 1 to 5 µl
Minimum Sample Volume	1 µl from 5 µl sample in 100 µl microvial, or 1 µl from 10 µl sample in 300 µl microvial
Carryover	Typically < 0.1 %, < 0.05 % with external needle cleaning
Sample Viscosity Range	0.2 to 50 cp
Replicate Injections Per Vial	1 to 99
Sample Capacity	100 x 2-ml vials in 1 tray 40 x 2-ml vials in ½ tray 15 x 6-ml vials in ½ tray (Agilent vials only)
Injection Cycle Time	Typically 50 s depending on draw speed and injection volume

Our Price: $5,125.00

Sale Price: $3,595.00

Money Saved: $1,530.00