|
|
|
|
VWR Symphony CO2 Water Jacketed Incubator, Model # 3074
The VWR Symphony CO2 Water Jacketed Incubator, Model # 3074 protects your cultures from unwanted heat loss by surrounding them with triple walled construction and a jacket of temperature conditioned water, making it an ideal choice for laboratories concerned with temperature fluctuations. Combining precise CO2 and temperature control with the use of a thermal conductivity sensor (T/C) makes the VWR Symphony Model 3074 a great choice for many different laboratory applications. The HEPA filtration system protects samples in the chamber from any airborne contaminants and airflow is assisted by a fan, all to help maintain optimal and uniform cell growth.
All of our equipment is fully tested to perform at factory
specifications before being shipped.
The VWR Symphony CO2 Water Jacketed Incubator, Model # 3074 includes:
- > 3 Shelves
- > Drain Tray
- > New HEPA Filter
- > Calibration
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
VWR Symphony CO2 Water Jacketed Incubator, Model # 3074 Specifications
Temperature:
|
|
Control
|
± 0.1°C
|
Temperature Range
|
Ambient +5°C to 55°C
|
Temperature Uniformity
|
± 0.3°C at 37°C
|
Low Temperature Tracking Alarm
|
Fixed at 1.0°C below setpoint
|
CO2:
|
|
CO2 Control
|
Better than ± 0.1%
|
CO2 Range
|
0-20%
|
Inlet Pressure
|
15 PSIG (1.034 bar), ± 5 PSIG
|
CO2 Sensor
|
T/C
|
Readability
|
0.1%
|
Low/High CO2 Tracking Alarm
|
Fixed at 1.0% below setpoint
|
Humidity:
|
|
RH
|
Ambient to 95% at 37°C
|
Humidity Pan
|
0.8 gal (3L) standard
|
Temperature Safety:
|
|
Sensor
|
Precision thermistor
|
Setability
|
0.1C
|
Construction:
|
|
Water Jacket Volume
|
11.7 gal (43.5L)
|
Interior Volume
|
6.5 cu ft. (184L)
|
Interior
|
Stainless Steel
|
Exterior
|
.18 Gauge, Cold rolled steel, Powder coated
|
Outlet Door Gasket
|
Four-sided, molded magnetic vinyl
|
Interior Door Gasket
|
Removable, Cleanable, Feather-edged silicone
|
VWR Symphony CO2 Water Jacketed Incubator, Model # 3074 Manual
Click Here to View the Technical Specs for the VWR Symphony CO2 Water Jacketed Incubator
- Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
- Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
- Inspect temperature, CO₂, and H₂O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
- Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
- Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
- Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
- Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
- Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
- Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
- Calibrate CO₂ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
- Monitor temperature and CO₂ stability over a 24-hour period, verifying consistent operation within specified ranges
- Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear
Technician Inspection and Recertification Checklist: Incubator
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
Task
|
Completed?
|
Remarks?
|
Inspect display for dim, flickering, or dead pixels; replace for readability
|
Completed
|
|
Examine external regulators for damage or malfunction; replace compromised parts
|
Completed
|
|
Inspect temperature, CO₂, and H₂O sensors for correct function and accuracy
|
Completed
|
|
Inspect internal wiring for frays, tears, or breakages; replace compromised wires
|
Completed
|
|
Verify software settings align with components and calibration specs; adjust if needed
|
Completed
|
|
Clean fan and remove dust/obstructions; replace if performance is substandard
|
Completed
|
|
Examine wheels and leveling mounts for structural integrity and balance
|
Completed
|
|
Inspect door gaskets and latches for wear or damage; replace to maintain seal
|
Completed
|
|
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy
|
Completed
|
|
Calibrate CO₂ level to 5% with Fyrite test kit for atmospheric precision
|
Completed
|
|
Monitor temperature and CO₂ stability over 24-hour period to verify consistency
|
Completed
|
|
Conduct cosmetic inspection to confirm quality of external surfaces and components
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
|
|
|
|