 |
 |
 |
|
Popular Alternative Choice
Boekel Scientific 151250 Digital Forced Air Incubator, 2.5 cu. ft. w/ Removable Light Shield, 115V
- Temperature range of Ambient +8°C to 70°C.
- Forced air convection provides excellent temperature stability, uniformity, and recovery time
- Bright easy-to-use digital display with built-in timer
- Energy efficient, low-power consumption design
Go to Product Details
Brand New!
VWR 1510E Incubator
The VWR 1510E Incubator is an efficient general purpose incubator. Efficient heating is supplied by economical, low-watt density strip heaters. Temperature range is from 5°C above ambient to 70°C with a temperature uniformity of ± 0.5°C at 37°C, regulated by a hydraulic temperature controller. Heat retention is aided by 2 inch fiberglass insulation and 0.5 inch silicone gasket. The interior chamber is 17" (W) x 12" (D) x 16.75" (H). All of our equipment will be fully tested to perform at factory specifications before being shipped.
The VWR 1510E Incubator includes:
- > 2 Shelves
- > Power Cord
- > Full 180 Day Parts and Labor Warranty
VWR 1510E Incubator Specifications
|
Temperature Range
|
Ambient +5° to 70°C
|
|
Temperature Uniformity
|
± 0.5°C at 37C
|
|
Interior Dimensions (W x D x H)
|
17 x 12 x 16.75 in
|
|
Exterior Dimensions (W x D x H)
|
21 x 16 x 25 in
|
|
Electrical Requirements
|
115V, 60Hz, 3A
|
- Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
- Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
- Inspect temperature, CO₂, and H₂O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
- Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
- Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
- Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
- Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
- Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
- Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
- Calibrate CO₂ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
- Monitor temperature and CO₂ stability over a 24-hour period, verifying consistent operation within specified ranges
- Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear
Technician Inspection and Recertification Checklist: Incubator
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
|
Task
|
Completed?
|
Remarks?
|
|
Inspect display for dim, flickering, or dead pixels; replace for readability
|
Completed
|
|
|
Examine external regulators for damage or malfunction; replace compromised parts
|
Completed
|
|
|
Inspect temperature, CO₂, and H₂O sensors for correct function and accuracy
|
Completed
|
|
|
Inspect internal wiring for frays, tears, or breakages; replace compromised wires
|
Completed
|
|
|
Verify software settings align with components and calibration specs; adjust if needed
|
Completed
|
|
|
Clean fan and remove dust/obstructions; replace if performance is substandard
|
Completed
|
|
|
Examine wheels and leveling mounts for structural integrity and balance
|
Completed
|
|
|
Inspect door gaskets and latches for wear or damage; replace to maintain seal
|
Completed
|
|
|
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy
|
Completed
|
|
|
Calibrate CO₂ level to 5% with Fyrite test kit for atmospheric precision
|
Completed
|
|
|
Monitor temperature and CO₂ stability over 24-hour period to verify consistency
|
Completed
|
|
|
Conduct cosmetic inspection to confirm quality of external surfaces and components
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
