Home > Incubators >

Thermolyne 37900 Culture Incubator, Model 137925

Our Price: $605.00

Condition: Fully Recertified and Tested to Perform at Manufacturer Specifications
Warranty: 180-Day Full Parts and Labor (Click for Info)
Typically Ships Within: 3 to 5 Business Days

Quantity in Stock:

Product Code: T37900

Qty:

Email me when Back-In-Stock

Description

Recertification Protocol

Thermolyne 37900 Culture Incubator, Model 137925

The Thermolyne 37900 Culture Incubator Model #137925 is a bench top analog incubator, using minimal space, but providing you with excellent incubation results. The aluminum lined chamber gives you excellent temperature uniformity. The thermometer on this specific piece is located on the back wall, allowing Petri dishes to be placed directly on the bottom of the chamber without overheating.

All of our equipment will be fully tested before being shipped.

INCLUDED:
The Thermolyne 37900 Culture Incubator, Model 137925 includes:

> Power Cord
> Full 180 Day Parts and Labor Warranty

Thermolyne 37900 Culture Incubator, Model 137925 Specifications

Temperature Range	Ambient +5 to 60C
Control	Analog
Interior Dimensions	10 x 8 in.
Exterior Dimensions	12.4 x 12.9 in.
Electrical Requirements	120V, 50/60Hz, 0.4A, 50W

Incubator Inspection and Recertification Checklist

Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
Inspect temperature, CO₂, and H₂O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
Calibrate CO₂ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
Monitor temperature and CO₂ stability over a 24-hour period, verifying consistent operation within specified ranges
Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear

Technician Inspection and Recertification Checklist: Incubator

The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment

Task	Completed?	Remarks?
Inspect display for dim, flickering, or dead pixels; replace for readability	Completed
Examine external regulators for damage or malfunction; replace compromised parts	Completed
Inspect temperature, CO₂, and H₂O sensors for correct function and accuracy	Completed
Inspect internal wiring for frays, tears, or breakages; replace compromised wires	Completed
Verify software settings align with components and calibration specs; adjust if needed	Completed
Clean fan and remove dust/obstructions; replace if performance is substandard	Completed
Examine wheels and leveling mounts for structural integrity and balance	Completed
Inspect door gaskets and latches for wear or damage; replace to maintain seal	Completed
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy	Completed
Calibrate CO₂ level to 5% with Fyrite test kit for atmospheric precision	Completed
Monitor temperature and CO₂ stability over 24-hour period to verify consistency	Completed
Conduct cosmetic inspection to confirm quality of external surfaces and components	Completed