 |
 |
 |
|
Thermo Sorvall Legend Micro 17 Centrifuge
Maximum Capacity
24 x 1.5/2.0ml
- Compact tabletop design ideal for biochemical and medical laboratories
- Quick Run function enables rapid acceleration for short spin applications
- Easy Control interface allows real-time monitoring and mid-run adjustments
- Maintenance-free induction motor ensures quiet, vibration-free operation
- Highly impact-resistant plastic housing with extra steel armor for durability
- Secure lid lock with emergency release for added safety
- Low noise level of 56 dBA for minimal lab disruption
- Fast acceleration and deceleration times enhance workflow efficiency
The Thermo Sorvall Legend Micro 17 Centrifuge is a compact and high-performance tabletop centrifuge designed for biochemical and medical laboratories. Accommodating up to 24 x 1.5/2.0ml tubes, it delivers rapid acceleration and deceleration, reaching speeds up to 13,300 RPM with a maximum RCF of 17,000 x g. Featuring an intuitive Easy Control interface, users can seamlessly adjust and monitor settings in real-time, even modifying parameters mid-run. The Quick Run function enables immediate high-speed acceleration for short spin applications, while the ultra-quiet, maintenance-free induction motor ensures smooth, vibration-free operation. Built with a highly impact-resistant plastic housing and reinforced with extra steel armor, this centrifuge includes a secure lid lock with emergency release for added safety. With a low noise level of just 56 dBA and a compact footprint, the Thermo Sorvall Legend Micro 17 Centrifuge is an efficient, user-friendly solution for high-speed microcentrifugation needs.
The Thermo Sorvall Legend Micro 17 Centrifuge is in excellent condition and will be fully tested to perform at factory specifications before being shipped.
The Thermo Sorvall Legend Micro 17 Centrifuge includes:
- > 24 x 1.5/2.0ml Fixed Angle Rotor with Lid (Cat. #: 75003424)
- > NIST Centrifuge Calibration and Preventative Maintenance Report
- > Power Cord
- > Operator's Guide
- > Full 180 Day Parts and Labor Warranty
Thermo Sorvall Legend Micro 17 Centrifuge Specifications
|
Maximum Speed
|
13,000 RPM
|
|
Maximum RCF
|
17,000 x g
|
|
Maximum Capacity
|
24 x 1.5/2.0ml
|
|
Timer
|
1 to 99 minutes, 1 minute increments + Hold Mode
|
|
Acceleration/Deceleration Rates
|
11/12 seconds
|
|
Maximum Noise Level
|
56 dB(A)
|
|
Dimensions (W x D x H)
|
22.5 x 24.3 x 35.2 cm(8.86 x 9.56 x 13.8 in)
|
|
Weight
|
23.1 lb. (10.5 kg)
|
|
Electrical Requirements
|
120V, 60 Hz, 2.6A, 180W
|
- Confirm the power supply output voltages match specified requirements for stable distribution to all internal components
- Measure and verify voltages at PCB test points to ensure accurate power delivery and circuit integrity
- Confirm rotor compatibility with the centrifuge model and check that rotor detection systems recognize the rotor type
- Inspect the exterior for any cosmetic or structural damage that could affect performance or safety
- Check the door mechanism alignment to ensure secure and smooth opening and closing
- Inspect and replace the gas strut with an OEM part to maintain proper door support and safety
- Examine the rotor chamber bowl for dents or damage and replace as needed to ensure safe operation
- Replace and confirm full functionality of all lid lock switches to maintain secure closure
- Inspect and lubricate the door lock mechanism, applying grease to the lid lock rail for smooth operation
- Test compressor functionality (if applicable) to ensure proper operation and consistent temperature control
- Conduct an 8-12 hour cycle test to validate consistent performance over prolonged use
- Confirm rotor motor stability, check for unusual noise, and assess mechanical integrity during operation
- Inspect the condensation drain and clear any clogs to prevent moisture buildup in the rotor chamber
- Verify RPM accuracy using an NIST-traceable tachometer and perform calibration as necessary
- Check the centrifuge error log to ensure zero recorded issues, confirming system reliability
Technician Inspection and Recertification Checklist: Centrifuges
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
| Task |
Completed? |
Remarks? |
| Confirm power supply output voltages match specified requirements |
Completed |
|
| Measure and verify voltages at PCB test points for accuracy |
Completed |
|
| Confirm rotor compatibility and detection for proper identification |
Completed |
|
| Inspect exterior for cosmetic or structural damage |
Completed |
|
| Check door mechanism alignment for secure opening and closing |
Completed |
|
| Inspect and replace gas strut with OEM part as needed |
Completed |
|
| Examine rotor chamber for dents or damage and replace if necessary |
Completed |
|
| Replace and confirm functionality of all lid lock switches |
Completed |
|
| Lubricate door lock mechanism and lid lock rail for smooth operation |
Completed |
|
| Test compressor (if applicable) for proper operation and cooling |
Completed |
|
| Run 8-12 hour cycle test to ensure consistent performance |
Completed |
|
| Check rotor motor for stability, noise, and integrity |
Completed |
|
| Inspect and clear condensation drain to prevent buildup |
Completed |
|
| Verify RPM accuracy with NIST traceable tachometer and calibrate |
Completed |
|
| Check centrifuge error log for zero recorded issues |
Completed |
|
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
