|
|
|
|
Thermo Scientific Digital Vortex Mixer, Cat. #: 88882009
The Thermo Scientific Digital Vortex Mixer, Cat. #: 88882009 is a highly efficient and versatile instrument designed for laboratory mixing. It features a digital display that provides precise monitoring of speed and time settings. This mixer offers a speed range of 200 to 3000 RPM, ensuring a wide range of mixing capabilities suitable for various applications. Speed accuracy is maintained within ±5%, ensuring consistent performance. The unit is designed with a 4 mm orbit and a platform diameter of 2.99 inches (7.6 cm), which is optimal for a variety of mixing containers.
The mixer has two operational modes: Continuous and Touch. In Continuous mode, it can quickly ramp up to a maximum speed of 3000 RPM in just 6 seconds, while in Touch mode, it reaches 1500 RPM in 3 seconds. This quick setup feature enhances efficiency in time-sensitive experiments. Additionally, it has two timer modes for added convenience. The down-counting timer is ideal for repeat tests, ensuring consistent mixing times for repeated procedures. It also features a timer mode that can be set for continuous operation or for a specific duration up to 99 minutes, with a time setting precision of 0.1 seconds.
All of our equipment is in excellent condition and will be fully tested to perform at factory specifications before being shipped.
The Thermo Scientific Digital Vortex Mixer, Cat. #: 88882009 includes:
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
Thermo Scientific Digital Vortex Mixer, Cat. #: 88882009 Specifications
Speed Range
|
200 to 3,000 RPM
|
Speed Accuracy
|
± 5%
|
Orbit
|
4 mm (0.157 in.)
|
Timer
|
0.1 seconds to 99 minutes
|
Platform Diameter
|
2.99 in. (7.6 cm)
|
Dimensions (L x W x H)
|
8.1 x 5.9 x 5.2 in. (20.5 x 15.1 x 13.1 cm)
|
Weight
|
14.3 lb. (6.5kg)
|
Electrical Requirements
|
AC100-240V, 50/60Hz, 6W
|
- Verify power supply and PCB output correct, stable voltages across all required circuits
- Confirm the correct platform head is installed according to specifications
- Inspect the display for dim or dead pixels, replacing any compromised sections to maintain clear visibility
- Confirm full functionality of all buttons and knobs, ensuring accurate input response
- Verify that touch, pulse, and continuous modes operate fully and as intended
- Inspect all internal wiring for breakages, tears, or wear, replacing any underperforming components to ensure reliability
- Disassemble and thoroughly clean the internal casing to remove any accumulated debris
- Check that the feet are intact and confirm the vortexer is properly balanced on a flat surface
- Conduct a comprehensive cosmetic inspection to ensure all exterior surfaces meet quality standards
Technician Inspection and Recertification Checklist: Vortexer
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
Task
|
Completed?
|
Remarks?
|
Verify power supply and PCB output stable, correct voltages across circuits
|
Completed
|
|
Confirm correct platform head is installed according to specifications
|
Completed
|
|
Inspect display for dim or dead pixels; replace compromised sections for clarity
|
Completed
|
|
Confirm functionality of all buttons and knobs for accurate input response
|
Completed
|
|
Verify full operation of touch, pulse, and continuous modes as intended
|
Completed
|
|
Inspect internal wiring for damage; replace underperforming components for reliability
|
Completed
|
|
Disassemble and clean internal casing to remove accumulated debris
|
Completed
|
|
Check feet for integrity and confirm vortexer is balanced on flat surface
|
Completed
|
|
Conduct comprehensive cosmetic inspection to ensure quality of exterior surfaces
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
|
|
|
|