Home > Incubators >

Thermo Forma 3851 CO2 Water Jacketed Incubator

Net 30 Terms and Financing Available

Our Price: $3,895.00

Condition: Fully Recertified and Tested to Perform at Manufacturer Specifications
Warranty: 180-Day Full Parts and Labor (Click for Info)
Typically Ships Within: 3 to 5 Business Days
Included Documentation: Calibration and Preventative Maintenance Report

Request a Formal Quote

Quantity in Stock:

Product Code: TH-3851

Qty:

Email me when Back-In-Stock

Description

Recertification Protocol

Thermo Forma 3851 CO2 Water Jacketed Incubator

The Thermo Forma 3851 Water-Jacketed CO2 Incubators combines precise CO2 control and temperature for proven water jacket technology. Temperature retention and quick recovery are especially important for researchers working with critical cell cultures. The Thermo Forma 3110 water jacketed incubator provides maximum thermal protection and quick recovery from swings in ambient temperature and power variations.

All of our equipment is fully tested to perform at factory specifications before being shipped.

INCLUDED:
The Thermo Forma 3851 CO2 Water Jacketed Incubator includes:

> 2 Shelves
> Drain Tray
> Power Cord
> Full 180 Day Parts and Labor Warranty

Thermo Forma 3851 CO2 Water Jacketed Incubator Specifications

Temperature:
Control	+/- 0.1C
Range	5C to Ambient
Uniformity	5C to Ambient
Tracking Alarm	Programmable High/Low
CO2/O2:
CO2/O2 Control	Better than +/- 0.1%
CO2 Range	0-20%
O2 Range	0-20%
Inlet Pressure	15 PSIG (1.0 bar)
CO2 Sensor	T/C or IR
O2 Ranger	Fuel Cell
Readability	0.1%
Tracking Alarm	User programmable High/Low
Humidity:
RH	Ambient or 95% @ 37C
Humidity Pan	3.2qt standard
Optional Display	In 1% increments
Inlet Pressure:
Maximun Per Channel	40.8 sq ft.
Standard Maximum	4,17
Safety:
Sensor	Precision thermistor
Controller	Independent Analog
Settings	0.1C
Construction:
Water Jacket Volume	11.7 gallons
Interior Volume	6.5 cu ft.
Interior	stainless steel
Exterior	coiled rolled stell
Outlet Door Gasket	Four sided magnetic vinyl
Interior Door Gasket	feather edge silicon.

Request a Formal Quote

Incubator Inspection and Recertification Checklist

Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
Inspect temperature, CO₂, and H₂O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
Calibrate CO₂ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
Monitor temperature and CO₂ stability over a 24-hour period, verifying consistent operation within specified ranges
Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear

Technician Inspection and Recertification Checklist: Incubator

The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment

Task	Completed?	Remarks?
Inspect display for dim, flickering, or dead pixels; replace for readability	Completed
Examine external regulators for damage or malfunction; replace compromised parts	Completed
Inspect temperature, CO₂, and H₂O sensors for correct function and accuracy	Completed
Inspect internal wiring for frays, tears, or breakages; replace compromised wires	Completed
Verify software settings align with components and calibration specs; adjust if needed	Completed
Clean fan and remove dust/obstructions; replace if performance is substandard	Completed
Examine wheels and leveling mounts for structural integrity and balance	Completed
Inspect door gaskets and latches for wear or damage; replace to maintain seal	Completed
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy	Completed
Calibrate CO₂ level to 5% with Fyrite test kit for atmospheric precision	Completed
Monitor temperature and CO₂ stability over 24-hour period to verify consistency	Completed
Conduct cosmetic inspection to confirm quality of external surfaces and components	Completed