 |
 |
 |
|
Scientific Industries Enviro-Genie Refrigerated Incubator Shaker SI-1200
The Enviro-Genie is a refrigerator, incubator, rotator, rocker, and stirrer all in one for the study of microorganisms and tissue cell growth under strictly controlled conditions of temperature and agitation. The Enviro-Genie is designed to provide the security of precise temperature control and uniformity for demanding incubation/refrigeration applications while having a small footprint. The chamber air is consistently circulating to ensure temperature uniformity throughout the chamber for all test samples. Microprocessor controls allow for precise control of shaking speeds, temperature, and time. All of our equipment is fully tested to perform at factory specifications before being shipped.
The Scientific Industries Enviro-Genie Refrigerated Incubator Shaker SI-1200 includes:
- > Rotating Platform
- > NIST Calibration and Preventative Maintenance Report
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
Scientific Industries Enviro-Genie Refrigerated Incubator Shaker SI-1200 Specifications
|
Rotating
|
1 to 35 rpm
|
|
Rocking
|
2 to 70 cycles per minute
|
|
Stirring
|
1 to 1000 rpm including stir reverse
|
|
Temperature Range
|
4 to 75°C (39 to 167°F)
|
|
Temperature Accuracy
|
± 0.2°C
|
|
Stability
|
± 0.1°C
|
|
Uniformity
|
± 0.5°C
|
|
Resolution
|
0.1C
|
|
Timer
|
Programmable to 99 hours
|
|
Alarm
|
Visible & audible, temperature & time
|
|
Product Weight
|
36 kg (80 lb)
|
|
Overall (D x W x H)
|
495 x 622 x 368 mm (19.5 x 24.5 x 14.5 in)
|
|
Dimensions (D x W x H)
|
254 x 362 x 260 mm (10 x 14.25 x 10.25 in)
|
|
Platform Capacity
|
4.5 kg (10 lb)
|
|
Chamber Volume
|
24 L
|
|
Electrical Requirements
|
120V, 5A, 60Hz
|
Scientific Industries Enviro-Genie SI-1200 Manual
 Click Here to View all the Technical Specs for the Enviro-Genie
- Examine the chamber glass for cracks or chips, replacing it as needed to maintain structural integrity.
- Inspect door seals for signs of wear or damage, replacing them to ensure a tight seal.
- Check the display for brightness and clarity, replacing any dim or dead pixels to maintain optimal visibility.
- Test all buttons to confirm full functionality and consistent responsiveness.
- Replace all platform assembly bearings to ensure smooth and reliable motion.
- Inspect the drive belt for wear, replacing it if torn or cracked to maintain performance.
- Examine all wiring for frays, tears, or breakages, addressing any issues for electrical safety.
- Verify each PCB test point, replacing any malfunctioning components to ensure system reliability.
- Check drive belt tension to confirm correct alignment and function.
- Confirm the compressor’s operation, cleaning condenser filter and fins for efficient cooling.
- Calibrate internal temperature accuracy using an NIST-traceable temperature probe.
- Measure and calibrate platform RPMs with an NIST-traceable tachometer to ensure precision.
- Conduct a final cosmetic inspection to verify all surfaces meet appearance standards.
Technician Inspection and Recertification Checklist
The Following Checklist Is to Be Performed on All Incoming and Outgoing Equipment
| Task |
Completed? |
Remarks? |
| Examine chamber glass for cracks or chips, replace as needed | Completed | |
| Inspect door seals for wear, replace to ensure tight seal | Completed | |
| Check display brightness, replace dim or dead pixels | Completed | |
| Test all buttons for full functionality and responsiveness | Completed | |
| Replace platform assembly bearings for reliable motion | Completed | |
| Inspect drive belt for wear, replace if torn or cracked | Completed | |
| Examine wiring for frays or breakages, repair as needed | Completed | |
| Verify PCB test points, replace faulty components | Completed | |
| Check drive belt tension for proper alignment | Completed | |
| Confirm compressor functionality, clean filter and fins | Completed | |
| Calibrate internal temperature with NIST probe | Completed | |
| Calibrate platform RPM with NIST-traceable tachometer | Completed | |
| Conduct cosmetic inspection for appearance standards | Completed | |
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
