 |
Precision Digital Water Bath, Cat # 51221048
The Precision Digital Water Bath, Category # 51221048 is in excellent condition. All of our equipment will be fully tested to perform at factory specifications before being shipped.
The Precision Digital Water Bath, Cat # 51221048 includes:
- > Bath Lid
- > Power Cord
- > Operator's Guide
- > Full 180 Day Parts and Labor Warranty
Precision Digital Water Bath, Cat #51221048 Specifications
|
Temperature Range
|
Ambient +5C to 100C
|
|
Temperature Uniformity
|
0.2C at 37C
|
|
Control
|
Digital
|
|
Capacity
|
5.5L (1.5 gal)
|
|
Bath Dimensions (L x W x H)
|
11.5 x 6 x 6 in (29.2 x 15.2 x 15.2
cm)
|
|
Electrical Requirements
|
120V, 50/60Hz, 2.5A
|
|
Temperature Sensitivity
|
0.1C at 37C
|
|
BTU Output
|
1025
|
|
Overall Dimensions (L x W x H)
|
15.25 x 8 x 9.75 in (38.7 x 20.3 x 24.8 cm)
|
Precision 280 Series Water Bath Manual
 Click Here to View all the Technical Specs for the Precision 2833
- Confirm power supply and PCB are outputting stable, correct voltages across all essential circuits to ensure reliable operation
- Inspect the display for any dim, flickering, or dead pixels, replacing any compromised sections to maintain full clarity and accurate readouts
- Verify that all buttons, knobs, and switches are functioning properly, providing precise and responsive control across all settings
- Conduct a thorough inspection of the water reservoir for any holes, rust, or other structural damage that may impact its integrity
- Fill the reservoir with water, checking closely for any external or internal leaks that could affect performance
- Examine the lid for any signs of wear or damage, replacing hinges and handles if necessary to ensure a secure and proper seal
- Inspect for any internal leaks originating from the water reservoir, confirming the unit’s internal plumbing integrity
- Conduct a comprehensive inspection of internal wiring for any breakages, tears, or wear; replace any underperforming or damaged components to maintain safe operation
- Examine internal insulation for signs of burns, breaks, or deterioration, replacing as needed to ensure thermal efficiency and safety
- Confirm that all feet are intact and that the bath sits level and balanced on a flat surface to prevent movement or instability
- Calibrate both temperature accuracy and uniformity using a NIST-traceable temperature probe, verifying compliance with specification standards
- Perform a detailed cosmetic inspection to confirm that all external surfaces and finishes meet aesthetic and quality standards
Technician Inspection and Recertification Checklist: Water Bath
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
|
Task
|
Completed?
|
Remarks?
|
|
Confirm power supply and PCB output stable, correct voltages across circuits
|
Completed
|
|
|
Inspect display for dim, flickering, or dead pixels; replace for clarity
|
Completed
|
|
|
Verify functionality of all buttons, knobs, and switches for responsive control
|
Completed
|
|
|
Inspect water reservoir for holes, rust, or structural damage
|
Completed
|
|
|
Fill reservoir with water; check for external or internal leaks
|
Completed
|
|
|
Examine lid for wear or damage; replace hinges or handles as needed
|
Completed
|
|
|
Inspect for internal leaks from water reservoir to confirm plumbing integrity
|
Completed
|
|
|
Check internal wiring for damage; replace underperforming components for safety
|
Completed
|
|
|
Examine internal insulation for burns, breaks, or deterioration; replace as needed
|
Completed
|
|
|
Confirm feet are intact and bath is balanced on flat surface
|
Completed
|
|
|
Calibrate temperature accuracy and uniformity with NIST-traceable probe
|
Completed
|
|
|
Perform cosmetic inspection to confirm quality of external surfaces and finishes
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
