Home > Freeze Dryer Systems >

Labconco FreeZone 6L -84C Plus Cascade Freeze Dry System

Net 30 Terms and Financing Available

Our Price: $15,695.00

Sale Price: $14,395.00

Money Saved: $1,300.00

Condition: Fully Recertified and Tested to Perform at Manufacturer Specifications
Warranty: 180-Day Full Parts and Labor (Click for Info)
Typically Ships Within: 3 to 5 Business Days

Request a Formal Quote

Quantity in Stock:1

Product Code: LA-6LPC84

Qty:

Description

Recertification Protocol

Technical Specification Sheet

Labconco FreeZone 6L -84C Plus Cascade Freeze Dry System

The Labconco FreeZone 6L -84C Plus Cascade Freeze Dry System (Cat. #: 7934022) is designed for light to moderate loads of low eutectic point samples. This freeze dryer system features an ice holding capacity of 6L, with the ability to remove a maximum of 4.1L of water over 24 hours. The Labconco FreeZone 6L -84C Plus Cascade Freeze Dry System also features an LCD screen that displays system operating parameters, set-up parameters, and alarm messages. This system includes a 24-Port Manifold along with a stainless steel collector chamber and coil. Some additional features include LED vacuum and temperature wave graphs, automatic start-up switch for collector cool down and vacuum pull down, hot gas defrost, and more.

All of our equipment is fully tested to perform at factory specifications before being shipped.

INCLUDED:
The Labconco FreeZone 6L -84C Plus Cascade Freeze Dry System includes:

> 24 Port Manifold
> New Edwards RV8 Vacuum Pump
> Vacuum Hose, Oil, Filter and All Hardware
> Operator's Guide
> Power Cords
> Full 180 Day Parts and Labor Warranty

Labconco FreeZone 6L -84C Plus Cascade Freeze Dry System Specifications

Ice Holding Capacity	6L
Lowest Temperature	-84C
Water Removal Over 24 Hours	4.1L
Manifold	24 Port Manifold
Electrical Requirements	115V, 60Hz, 16A
Vacuum Pump Displacement Required	98L/min or larger
Ambient Temperature Range	5C to 40C
Dimensions (W x D x H)	32.2 x 28 x 36.3 in. (81.8 x 71.1 x 92.2 cm)
Weight	288 lbs. (131 kg.)
Conformance	CAN/CSA C22.2, UL

Downloads

Technical Specification Download

Operator's Manual Download

Request a Formal Quote

Recertification Inspection Protocol

Inspect the display for pixel clarity and brightness issues; replace any dim or defective pixels to ensure optimal visual quality.
Test each button for responsiveness, resistance, and continuity; replace any buttons that show wear or unresponsiveness.
Check the acrylic/glass lid for structural integrity, looking for cracks or chips; replace if any damage is found.
Examine all external gasket seals for elasticity, cracks, or tears; replace compromised seals with OEM-approved parts.
Remove and replace all manifold ports with new OEM parts, ensuring proper fit and sealing to maintain system integrity.
Drain and replace the oil, verifying the new oil’s viscosity and particulate levels fall within operational standards.
Conduct diagnostic checks on all PCB test points, replacing any malfunctioning components to maintain circuit integrity.
Inspect all internal rubber connections and gaskets for cracks or brittleness; replace compromised parts as needed.
Disassemble and clean the condenser coils and fan assembly to remove dust; replace worn components to ensure efficiency.
Confirm the start capacitor for the refrigeration system meets the manufacturer-specified capacitance range; replace if readings deviate.
Test and calibrate all internal sensors and safety switches, ensuring accurate readings and replacing any faulty components.
Verify displayed temperatures by cross-referencing with independent calibrated probes; recalibrate the system if discrepancies are detected.
Check vacuum pressure using an independent gauge, aiming for ~0.40 mbar; address any leaks or inefficiencies affecting vacuum levels.
Confirm the system achieves and maintains low temperatures (~-50°C or ~-80°C) using certified measurement tools; troubleshoot as necessary.
Inspect all external surfaces, labels, and interfaces for cosmetic wear; address any scratches, blemishes, or visible signs of damage.

Technician Inspection and Recertification Checklist

The Following Checklist Is to Be Performed on All Incoming and Outgoing Equipment

Task	Completed?	Remarks?
Inspect display for pixel issues and replace if needed	Completed
Test button functionality and replace any defective buttons	Completed
Examine door seal and lock functionality; replace if compromised	Completed
Conduct PCB test point diagnostics and replace as needed	Completed
Verify compressor and internal fan functionality	Completed
Confirm temperature probe accuracy with NIST-traceable probe	Completed
Inspect all wiring for frays, tears, or breakages	Completed
Test start capacitor capacitance range; replace if needed	Completed
Replace all internal filters and clean condenser fins	Completed
Test alarm battery for full functionality	Completed
Run 72-hour test with data recorder to confirm stable temperatures	Completed
Conduct cosmetic inspection and address any issues	Completed