Home > Freeze Dryer Systems >

Labconco FreeZone 6L -84C Console Freeze Dryer System

Net 30 Terms and Financing Available

Our Price: $15,995.00

Condition: Fully Recertified and Tested to Perform at Manufacturer Specifications
Warranty: 180-Day Full Parts and Labor (Click for Info)
Typically Ships Within: 3 to 5 Business Days

Request a Formal Quote

Quantity in Stock:1

Product Code: LA-6L84CFDS

Qty:

Description

Recertification Protocol

Technical Specification Sheet

Labconco FreeZone 6L -84C Console Freeze Dryer System

The Labconco FreeZone 6L -84C Console Freeze Dryer System (Cat #: 710611000) is designed for lyophilizing moderate to large sample loads or numerous small container batches. The console features a front viewing window, interior space for a vacuum pump, and accommodation for a large tray dryer such as the FreeZone Stoppering Tray Dryers. These models offer the broadest range of built-in options. The upright stainless steel collector coil holds 6 liters of ice before defrosting. A single 3/4 hp HCFC/CFC-free refrigeration system cools the collector to -84°C (-119°F), suitable for aqueous samples. Also featured is the Lyo-Works OS, which provides a real time display of collector temperature, vacuum level and optional End-Zone end point detection system, shown on a 5" full color, capacitive touch screen.

All of our equipment is fully tested to perform at factory specifications before being shipped.

INCLUDED:
The Labconco FreeZone 6L -84C Console Freeze Dryer System includes:

> New Edwards RV8 Vacuum Pump
> 12 Port Drying Chamber
> Edwards EMF10 Oil Mist Filter NW25
> Vacuum Hose, Pump Oil, and All Hardware
> Power Cords
> Operator's Manual
> Full 180 Day Parts and Labor Warranty

Labconco FreeZone 6L -84C Console Freeze Dryer System Specifications

Ice Holding Capacity	6L
Lowest Temperature	-84C
Water Removal Over 24 Hours	4L
Manifold	12 Port Drying Chamber
Vacuum Pump Displacement Required	98L/min
Dimensions (W x D x H)	31.8 x 29.6 x 36.6 in. (80.7 x 75.1 x 92.9 cm)
Weight	299 lb. (135.6 kg)
Conformance	CAN/CSA C22.2, UL
Electrical Requirements	115V, 60Hz, 16A

Downloads

Technical Specification Download

Operator's Manual Download

Request a Formal Quote

Recertification Inspection Protocol

Inspect the display for pixel clarity and brightness issues; replace any dim or defective pixels to ensure optimal visual quality.
Test each button for responsiveness, resistance, and continuity; replace any buttons that show wear or unresponsiveness.
Check the acrylic/glass lid for structural integrity, looking for cracks or chips; replace if any damage is found.
Examine all external gasket seals for elasticity, cracks, or tears; replace compromised seals with OEM-approved parts.
Remove and replace all manifold ports with new OEM parts, ensuring proper fit and sealing to maintain system integrity.
Drain and replace the oil, verifying the new oil’s viscosity and particulate levels fall within operational standards.
Conduct diagnostic checks on all PCB test points, replacing any malfunctioning components to maintain circuit integrity.
Inspect all internal rubber connections and gaskets for cracks or brittleness; replace compromised parts as needed.
Disassemble and clean the condenser coils and fan assembly to remove dust; replace worn components to ensure efficiency.
Confirm the start capacitor for the refrigeration system meets the manufacturer-specified capacitance range; replace if readings deviate.
Test and calibrate all internal sensors and safety switches, ensuring accurate readings and replacing any faulty components.
Verify displayed temperatures by cross-referencing with independent calibrated probes; recalibrate the system if discrepancies are detected.
Check vacuum pressure using an independent gauge, aiming for ~0.40 mbar; address any leaks or inefficiencies affecting vacuum levels.
Confirm the system achieves and maintains low temperatures (~-50°C or ~-80°C) using certified measurement tools; troubleshoot as necessary.
Inspect all external surfaces, labels, and interfaces for cosmetic wear; address any scratches, blemishes, or visible signs of damage.

Technician Inspection and Recertification Checklist

The Following Checklist Is to Be Performed on All Incoming and Outgoing Equipment

Task	Completed?	Remarks?
Inspect display for pixel issues and replace if needed	Completed
Test button functionality and replace any defective buttons	Completed
Examine door seal and lock functionality; replace if compromised	Completed
Conduct PCB test point diagnostics and replace as needed	Completed
Verify compressor and internal fan functionality	Completed
Confirm temperature probe accuracy with NIST-traceable probe	Completed
Inspect all wiring for frays, tears, or breakages	Completed
Test start capacitor capacitance range; replace if needed	Completed
Replace all internal filters and clean condenser fins	Completed
Test alarm battery for full functionality	Completed
Run 72-hour test with data recorder to confirm stable temperatures	Completed
Conduct cosmetic inspection and address any issues	Completed