 |
 |
 |
|
Labconco 4420320 FlaskScrubber Glassware Washer, Undercounter
The Labconco 4420320 FlaskScrubber Glassware Washer, Undercounter is designed to wash and dry narrow-neck laboratory glassware. The included lower spindle rack can hold up to 36 pieces each of narrow-neck glassware such as volumetric flasks (removeable spindles not included with racks). Water and detergent are pumped through the spindles to reach the innermost areas of the glassware, ensuring an efficient clean. Following this, forced air drying through the spindles ensures thorough drying inside and out. The Labconco 4420320 FlaskScrubber Glassware Washer, Undercounter allows for the user to select pre-programmed wash cycles or program customized wash cycles to meet application requirements. Wash cycles may be programmed to provide steam and the use of purified water in the rinse cycles, allowing the user to choose the best conditions possible for their glassware. Features
- Achieve higher water temperatures for enhanced washing, faster drying, and sanitizing
- LCD information center for customizing cycles and monitoring operations, including internal water temperature (°C or °F) and alarms
- High water circulation rates for thorough cleaning: 96 gal/min. (363L/min.) when operated on 115V, 60Hz
- Dual pumps: one for washing and one for draining, to reduce potential for cross-contamination
- Built-in purified water pump brings unpressurized or pressurized purified water into tank for up to six pure water rinses
- Built-in steam generator produces hot vapor to penetrate and remove dried residue for cleaner glassware
- Manual-fill dispensers for detergent (powder or liquid) or rinse aid solution
- Two user-set cycle programs
- User-set delayed start (up to 8 hours)
- Environmentally Friendly: Item contains environmental attributes or features (e.g. water conserving, lead-free, etc.) as described in the item detail
All of our equipment is fully tested to perform at factory specifications before being shipped.
The Labconco 4420320 FlaskScrubber Glassware Washer, Undercounter includes:
- > Lower Spindle Rack
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
- > Power Supply Requires Electrician to Hard-Wire Upon Installation
Labconco 4420320 FlaskScrubber Glassware Washer, Undercounter Specifications
|
Minimum Fill Water Temperature
|
49°C (120°F)
|
|
Water Consumption
|
13L (3.4 gal.)
|
|
Minimum Feed Water Pressure
|
20 psi (138 kPa)
|
|
Maximum Feed Water Pressure
|
120 psi (827 kPa)
|
|
Minimum Purified Feed Water Pressure
|
0 psi (0 kPa)
|
|
Heat Rejected from Washer
|
Less than 104 BTU/min
|
|
Water Heating Rate
|
0.9°C/min (1.6°F/min)
|
|
Material
|
Type 304 Stainless Steel
|
|
Style
|
Undercounter
|
|
Dimensions (W x D x H)
|
24.1 x 27.4 x 36.1 in. (61.2 x 69.6 x 91.7 cm)
|
|
Weight
|
206 lb. (93.4 kg)
|
|
Electrical Requirements
|
115V, 60Hz, 16A, 20A circuit breaker required
|
- Inspect the display for pixel clarity and brightness issues; replace any dim or defective pixels for optimal performance.
- Test each button for responsiveness, resistance, and continuity, replacing any that do not meet operational standards.
- Verify touchscreen functionality (if applicable), ensuring consistent response across all touch points.
- Check the door seal and lock for airtight closure and secure operation, replacing any compromised parts.
- Inspect rubber hoses for wear, tears, or cracks, replacing any that compromise system integrity.
- Inspect for internal or external leakage, addressing and sealing any detected points of vulnerability.
- Check all wiring for integrity, inspecting for frays, tears, or breakages, and replace compromised sections.
- Run the system in continuous cycle mode, monitoring for operational errors to ensure reliable performance.
- Confirm all sensors are activated and responsive using internal diagnostics, recalibrating or replacing any faulty ones.
- Conduct a cosmetic inspection of external surfaces, verifying cleanliness and addressing visible wear to meet standards.
Technician Inspection and Recertification Checklist
The Following Checklist Is to Be Performed on All Incoming and Outgoing Equipment
| Task |
Completed? |
Remarks? |
| Inspect display for pixel issues and replace if needed | Completed | |
| Test button functionality and replace any defective buttons | Completed | |
| Verify touchscreen functionality (if applicable) | Completed | |
| Check door seal and lock functionality; replace if compromised | Completed | |
| Inspect rubber hoses for wear, tears, or cracks | Completed | |
| Check for internal or external leakage and address as needed | Completed | |
| Inspect wiring for frays, tears, or breakages | Completed | |
| Run continuous cycle mode and monitor for errors | Completed | |
| Confirm all sensors are activated and functional | Completed | |
| Conduct cosmetic inspection and address visible wear | Completed | |
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
