Home > Centrifuges >

Hettich Universal 320 Centrifuge

Net 30 Terms and Financing Available

Our Price: $3,295.00

Condition: Fully Recertified and Tested to Perform at Manufacturer Specifications
Warranty: 180-Day Full Parts and Labor (Click for Info)
Typically Ships Within: 3 to 5 Business Days
Included Documentation: NIST Centrifuge Calibration and Preventative Maintenance Report

Request a Formal Quote

Quantity in Stock:1

Product Code: H-320

Qty:

Description

Recertification Protocol

Technical Specification Sheet

Hettich Universal 320 Centrifuge

The Hettich Universal 320 Centrifuge reaches maximum speeds up to 15,000 RPM with a maximum RCF up to 21,382 x g. Timer up to 99 minutes, featuring 10 programmable run memories. Safety features include powered lid locking, lid dropping protection, lid lock and hold, emergency lid lock release, motor overheating protection, chamber overheating protection, and imbalance switch-off. This rotor reaches maximum 4,000 RPM.

All of our equipment is fully tested to perform at factory specifications before being shipped.

INCLUDED:
The Hettich Universal 320 Centrifuge includes:

> Hettich 1619 Swing Out Rotor and 1681 Buckets
> NIST Centrifuge Calibration and Preventative Maintenance Report
> Power Cord
> Operator's Guide
> Full 180 Day Parts and Labor Warranty

Hettich Universal 320 Centrifuge, Cat # 1401-01 Specifications

Maximum Speed	15,000 RPM (fixed angle rotor)
Maximum RCF	21,382 x g
Timer	Up to 99 minutes
Dimensions (H x W x D)	346 x 395 x 520 mm
Electrical Requirements	100-127V, 50/60Hz
Refrigeration	No Refrigeration

Preventative Maintenance Performed on The Hettich Universal 320 Centrifuge, Cat # 1401-01

Door Latch Assembly Checked for Full Function
Door Hinges are Checked and Lubed as Needed
Drive Belt is Checked for Rips and Tears and Replaced if Needed
Rotors and O-rings are Lubed as Needed
Lamps and Display are Checked and Replaced if Dim
Line Cord is Checked for Signs of Fray or Damage and Replaced Accordingly
Internal Circuitry is Checked for Faulty/Shorted Components and Replaced Accordingly

Hettich Universal 320 Manual

Click Here to View all the Technical Specs for the Universal 320

Request a Formal Quote

Centrifuge Inspection and Recertification Checklist

Confirm the power supply output voltages match specified requirements for stable distribution to all internal components
Measure and verify voltages at PCB test points to ensure accurate power delivery and circuit integrity
Confirm rotor compatibility with the centrifuge model and check that rotor detection systems recognize the rotor type
Inspect the exterior for any cosmetic or structural damage that could affect performance or safety
Check the door mechanism alignment to ensure secure and smooth opening and closing
Inspect and replace the gas strut with an OEM part to maintain proper door support and safety
Examine the rotor chamber bowl for dents or damage and replace as needed to ensure safe operation
Replace and confirm full functionality of all lid lock switches to maintain secure closure
Inspect and lubricate the door lock mechanism, applying grease to the lid lock rail for smooth operation
Test compressor functionality (if applicable) to ensure proper operation and consistent temperature control
Conduct an 8-12 hour cycle test to validate consistent performance over prolonged use
Confirm rotor motor stability, check for unusual noise, and assess mechanical integrity during operation
Inspect the condensation drain and clear any clogs to prevent moisture buildup in the rotor chamber
Verify RPM accuracy using an NIST-traceable tachometer and perform calibration as necessary
Check the centrifuge error log to ensure zero recorded issues, confirming system reliability

Technician Inspection and Recertification Checklist: Centrifuges

The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment

Task	Completed?	Remarks?
Confirm power supply output voltages match specified requirements	Completed
Measure and verify voltages at PCB test points for accuracy	Completed
Confirm rotor compatibility and detection for proper identification	Completed
Inspect exterior for cosmetic or structural damage	Completed
Check door mechanism alignment for secure opening and closing	Completed
Inspect and replace gas strut with OEM part as needed	Completed
Examine rotor chamber for dents or damage and replace if necessary	Completed
Replace and confirm functionality of all lid lock switches	Completed
Lubricate door lock mechanism and lid lock rail for smooth operation	Completed
Test compressor (if applicable) for proper operation and cooling	Completed
Run 8-12 hour cycle test to ensure consistent performance	Completed
Check rotor motor for stability, noise, and integrity	Completed
Inspect and clear condensation drain to prevent buildup	Completed
Verify RPM accuracy with NIST traceable tachometer and calibrate	Completed
Check centrifuge error log for zero recorded issues	Completed