 |
Popular Alternative Choice
Thermo Scientific Forma 320 CO2 Incubator
- Optimized for tissue and cell sample incubation with precise environment controls.
- Temperature control from Ambient +5°C to 50°C and CO2 control from 0 to 20%.
- Equipped with audible and visual alarms for deviations in parameters.
- 6.5 cu. ft. chamber provides ample space and includes an internal access port.
Go to Product Details
Fully Recertified!
Heracell 150 CO2 Incubator
The HERAcell 150 CO2 copper chamber incubator provides a safe, stable,
precisely-controlled cell culture
environment with the proven contamination control and convenience offered by
ContraCon. The HeraCell 150 utilizes a
thermal conductivity (TC) sensor with accurate gas sensor
technology. The incubator's air jacket maintains temperature uniformity and quick set-up time.
The ContraCon 90°C automatic decontamination routine decontaminates the
entire interior and water reservoir without the need to remove sensors and
fittings (in independent tests, ContraCon
was proven to completely eliminate mycoplasma).
This incubator is currently only available with an Aluminum interior, not Copper.
All of our equipment is fully tested to perform at factory specifications before being shipped.
The Heracell 150 CO2 Incubator includes:
- > 2 Shelves
- > Calibration and Preventative Maintenance Report
- > Power Cord
- > Operator's Manual
- > Full 180 Day Parts and Labor Warranty
Heracell 150 CO2 Incubator Specifications
|
Temperature Control Range
|
ambient +3 to + 55°C
|
|
Temperature Deviation
time/spatial
|
± 0.1 / ± 0.5 °C
|
|
Ambient Temperature Range
|
+ 18°C to +33°C
|
|
CO2 Measure Control Range
|
TC sensor 0 to 20%
|
|
CO2 Control Accuracy
|
± 0.1%
|
|
Humidity (constant)
|
≥ 95% rH
|
|
Humidity fill amount/
water quality
|
max. 3/ distilled or
autoclaved
|
|
Dimensions (W x H x D)
|
25.1 x 34.1 x 30.2"
|
|
Total Volume
|
5.4 cu.ft (150L)
|
|
Weight
|
165lb
|
Heracell 150 CO2 Incubator Manual
 Click Here to View all the Technical Specs for the Heracell 150
- Inspect the display for any dim, flickering, or dead pixels, replacing any affected areas to maintain full readability and operational clarity
- Thoroughly examine external regulators for any signs of damage, wear, or malfunction (if applicable), replacing any compromised parts
- Inspect temperature, CO₂, and H₂O sensors (if applicable), ensuring each sensor is functioning correctly and accurately reporting conditions
- Conduct a detailed inspection of all internal wiring for frays, tears, or breakages; replace any compromised wires to ensure safe and reliable connections
- Verify that software settings align with the internal components and calibration specifications, adjusting configurations as needed for accurate operation
- Inspect and clean the fan, ensuring it is free from dust or obstructions; replace if performance is below required standards
- Examine wheels and leveling mounts for structural integrity, ensuring proper balance and stability for safe operation
- Inspect door gaskets and latches for any signs of wear or damage, replacing if necessary to maintain a secure seal and optimal environmental control
- Calibrate temperature accuracy at 37°C using a NIST-traceable probe, confirming it meets required tolerances
- Calibrate CO₂ level to 5% using a Fyrite combustion test kit (if applicable), ensuring precise atmospheric conditions
- Monitor temperature and CO₂ stability over a 24-hour period, verifying consistent operation within specified ranges
- Conduct a thorough cosmetic inspection to confirm all external surfaces and components meet quality standards, free from visible damage or wear
Technician Inspection and Recertification Checklist: Incubator
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
|
Task
|
Completed?
|
Remarks?
|
|
Inspect display for dim, flickering, or dead pixels; replace for readability
|
Completed
|
|
|
Examine external regulators for damage or malfunction; replace compromised parts
|
Completed
|
|
|
Inspect temperature, CO₂, and H₂O sensors for correct function and accuracy
|
Completed
|
|
|
Inspect internal wiring for frays, tears, or breakages; replace compromised wires
|
Completed
|
|
|
Verify software settings align with components and calibration specs; adjust if needed
|
Completed
|
|
|
Clean fan and remove dust/obstructions; replace if performance is substandard
|
Completed
|
|
|
Examine wheels and leveling mounts for structural integrity and balance
|
Completed
|
|
|
Inspect door gaskets and latches for wear or damage; replace to maintain seal
|
Completed
|
|
|
Calibrate temperature at 37°C with NIST-traceable probe to confirm accuracy
|
Completed
|
|
|
Calibrate CO₂ level to 5% with Fyrite test kit for atmospheric precision
|
Completed
|
|
|
Monitor temperature and CO₂ stability over 24-hour period to verify consistency
|
Completed
|
|
|
Conduct cosmetic inspection to confirm quality of external surfaces and components
|
Completed
|
|
To View More of Our Recertification Protocol Click Here
|
|
|
Satisfied Customer 
