 |
 |
 |
|
Boekel Jitterbug Incubator Shaker
The Boekel Jitterbug Incubator Shaker #130000 is a combination incubator, timer, and shaker that can accommodate two standard microplates or strip trays. Independently set temperature, shaking speed, and mixing duration for excellent temperature uniformity within chamber design. The mixer features gradual steps in mixing speeds from gentle agitation to vigorous mixing with eight settings for either continuous operation or three-second pulses. A smoke tint plexi-glass cover protects the plates, shielding samples from light and insulating through incubation. Smooth, quiet operation in a rugged mixer built for a variety of applications, including immunoassay, PCR, and other microplate procedures. The Jitterbug is in excellent condition and is fully tested to perform at factory specifications before being shipped.
The Boekel Jitterbug Incubator Shaker includes:
- > Lid
- > NIST Calibration and Preventative Maintenance Report
- > Power Cord
- > Full 180 Day Parts and Labor Warranty
Boekel Jitterbug Incubator Shaker Specifications
|
Speed Range
|
575 to 1500 rpm
|
|
Orbit
|
Approximately 1mm
|
|
Mechanism
|
Rotating counterweight
|
|
Temperature Range
|
Ambient to 40°C
|
|
Temperature Resolution
|
0.1°C
|
|
Temperature Uniformity
|
Better than ± 0.4°C with cover
|
|
Warm Up Time
|
Typically 15 minutes
|
|
Timer Range
|
1 second to 99 min. 59 sec.
|
|
Pulse Operation
|
1500 rpm for 3 seconds
|
|
Electrical
|
115V, 50/60Hz
|
|
Dimensions (W x D x H)
|
10 x 10 x 4 in (25.4 x 25.4 x 10.2 cm)
|
Boekel Jitterbug Incubator Shaker Manual
 Click Here to View all the Technical Specs for the Boekel Jitterbug
Boekel Jitterbug Incubator/Shaker - Marshall Scientific
- Examine the chamber glass for cracks or chips, replacing it as needed to maintain structural integrity.
- Inspect door seals for signs of wear or damage, replacing them to ensure a tight seal.
- Check the display for brightness and clarity, replacing any dim or dead pixels to maintain optimal visibility.
- Test all buttons to confirm full functionality and consistent responsiveness.
- Replace all platform assembly bearings to ensure smooth and reliable motion.
- Inspect the drive belt for wear, replacing it if torn or cracked to maintain performance.
- Examine all wiring for frays, tears, or breakages, addressing any issues for electrical safety.
- Verify each PCB test point, replacing any malfunctioning components to ensure system reliability.
- Check drive belt tension to confirm correct alignment and function.
- Confirm the compressor’s operation, cleaning condenser filter and fins for efficient cooling.
- Calibrate internal temperature accuracy using an NIST-traceable temperature probe.
- Measure and calibrate platform RPMs with an NIST-traceable tachometer to ensure precision.
- Conduct a final cosmetic inspection to verify all surfaces meet appearance standards.
Technician Inspection and Recertification Checklist
The Following Checklist Is to Be Performed on All Incoming and Outgoing Equipment
| Task |
Completed? |
Remarks? |
| Examine chamber glass for cracks or chips, replace as needed | Completed | |
| Inspect door seals for wear, replace to ensure tight seal | Completed | |
| Check display brightness, replace dim or dead pixels | Completed | |
| Test all buttons for full functionality and responsiveness | Completed | |
| Replace platform assembly bearings for reliable motion | Completed | |
| Inspect drive belt for wear, replace if torn or cracked | Completed | |
| Examine wiring for frays or breakages, repair as needed | Completed | |
| Verify PCB test points, replace faulty components | Completed | |
| Check drive belt tension for proper alignment | Completed | |
| Confirm compressor functionality, clean filter and fins | Completed | |
| Calibrate internal temperature with NIST probe | Completed | |
| Calibrate platform RPM with NIST-traceable tachometer | Completed | |
| Conduct cosmetic inspection for appearance standards | Completed | |
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
