 |
 |
 |
|
Beckman Coulter Allegra 6R Refrigerated Centrifuge
Temperature Range
-5° to 25°C
- Smart balance technology ensures balanced operation for consistent and reliable results.
- Accommodates a wide range of vessels including 1.5 ml tubes to 750 ml bottles, microplates, specialty bottles, and blood bags.
- Automatic rotor imbalance detection monitors and automatically shuts down the centrifuge in case of severe imbalance.
- Auto door interlock ensures the door locks automatically during a run and can only be opened under safe conditions.
- Secondary manual lock prevents operator contact with spinning rotors.
- Electromechanical door lock system ensures the door remains securely close during operation.
The Beckman Allegra 6R Refrigerated Centrifuge features
smart balance technology and has a high capacity with the
GH-3.8 swing bucket rotor. This benchtop centrifuge and its rotor can accommodate a wide range of
vessels, from 1.5 ml tubes to 750 ml bottles and generally including tubes,
bottles, microplates, specialty bottles, and blood bags.
The Allegra 6 reaches maximum speeds up to 8,000 RPM with a fixed angle rotor. Refrigerated temperature range from -5°C to 25°C. Features automatic rotor imbalance detection, auto door interlock, rugged drive, and fine-tuned suspension for performance, reliability, and safety in the lab. The Allegra 6R is ideal for cell culture, plasma, and other general purpose separations. This rotor reaches a maximum speed of 3,750 RPM.
All of our equipment is fully tested to perform at factory specifications before being shipped.
Please confirm this rotor meets your application needs and request a different rotor, if necessary. Available rotors can be found in our Rotor Compatibility Guide.
The Beckman Coulter Allegra 6R Refrigerated Centrifuge includes:
- > GH-3.8 Swing Bucket Rotor and Buckets
- > 1 Set of 15ml Adapters
- > 1 Set of 50ml Adapters
- > NIST Centrifuge Calibration and Preventative Maintenance Report
- > Power Cord
- > Full 180 Day Parts and Labor Warranty
Beckman Allegra 6R Refrigerated Centrifuge Specifications
|
Maximum speed (RPM)
|
Fixed angle rotor: 8,000
Swinging bucket rotor: 4,730
|
|
Maximum capacity
|
4 x 750ml
|
|
Temperature range
|
-5° to 25°C
|
|
Run time
|
0 – 30 minute, hold timer
|
|
Driver
|
Direct drive with replacement brushes
|
|
Accel/Decel rates
|
1 / 3
|
|
Maximum noise output
|
< 60 dB
|
|
Dimensions (W x D x H)
|
30 x 26 x 15.5 in (door closed)
30 x 26 x 37 in (door open)
|
|
Weight
|
197 lbs
|
- Door Latch Assembly Checked for Full Function
- Door Hinges are Checked and Lubed as Needed
- Drive Belt is Checked for Rips and Tears and Replaced if Needed
- Rotors and O-rings are Lubed as Needed
- Lamps and Display are Checked and Replaced if Dim
- Line Cord is Checked Signs of Fray or Damage and Replaced Accordingly
- Internal Circuitry is Checked for Faulty/Shorted Components and Replaced Accordingly
- Confirm the power supply output voltages match specified requirements for stable distribution to all internal components
- Measure and verify voltages at PCB test points to ensure accurate power delivery and circuit integrity
- Confirm rotor compatibility with the centrifuge model and check that rotor detection systems recognize the rotor type
- Inspect the exterior for any cosmetic or structural damage that could affect performance or safety
- Check the door mechanism alignment to ensure secure and smooth opening and closing
- Inspect and replace the gas strut with an OEM part to maintain proper door support and safety
- Examine the rotor chamber bowl for dents or damage and replace as needed to ensure safe operation
- Replace and confirm full functionality of all lid lock switches to maintain secure closure
- Inspect and lubricate the door lock mechanism, applying grease to the lid lock rail for smooth operation
- Test compressor functionality (if applicable) to ensure proper operation and consistent temperature control
- Conduct an 8-12 hour cycle test to validate consistent performance over prolonged use
- Confirm rotor motor stability, check for unusual noise, and assess mechanical integrity during operation
- Inspect the condensation drain and clear any clogs to prevent moisture buildup in the rotor chamber
- Verify RPM accuracy using an NIST-traceable tachometer and perform calibration as necessary
- Check the centrifuge error log to ensure zero recorded issues, confirming system reliability
Technician Inspection and Recertification Checklist: Centrifuges
The Following Checklist Is to Be Performed on All Incoming and Outgoing Pieces of Equipment
| Task |
Completed? |
Remarks? |
| Confirm power supply output voltages match specified requirements |
Completed |
|
| Measure and verify voltages at PCB test points for accuracy |
Completed |
|
| Confirm rotor compatibility and detection for proper identification |
Completed |
|
| Inspect exterior for cosmetic or structural damage |
Completed |
|
| Check door mechanism alignment for secure opening and closing |
Completed |
|
| Inspect and replace gas strut with OEM part as needed |
Completed |
|
| Examine rotor chamber for dents or damage and replace if necessary |
Completed |
|
| Replace and confirm functionality of all lid lock switches |
Completed |
|
| Lubricate door lock mechanism and lid lock rail for smooth operation |
Completed |
|
| Test compressor (if applicable) for proper operation and cooling |
Completed |
|
| Run 8-12 hour cycle test to ensure consistent performance |
Completed |
|
| Check rotor motor for stability, noise, and integrity |
Completed |
|
| Inspect and clear condensation drain to prevent buildup |
Completed |
|
| Verify RPM accuracy with NIST traceable tachometer and calibrate |
Completed |
|
| Check centrifuge error log for zero recorded issues |
Completed |
|
To View More of Our Recertification Protocol Click Here
|
|
|
 |
|
 |
|
